Smart Yo-yo
| Line 12: | Line 12: | ||
In traditional yo-yos, the whole body of the yo-yo is one part and has a string wrapped around the middle. It "sleeps" by spinning on the string. Since this depends on many varying characteristics of the string, including how much friction is involved or how tight the string is tied, it is very unpredictable. However with the bearing this modle allows for longer and more reliable spin and sleep times. | In traditional yo-yos, the whole body of the yo-yo is one part and has a string wrapped around the middle. It "sleeps" by spinning on the string. Since this depends on many varying characteristics of the string, including how much friction is involved or how tight the string is tied, it is very unpredictable. However with the bearing this modle allows for longer and more reliable spin and sleep times. | ||
| − | Computer models were created of each of the following parts. Using the current model as a guide and accepted values for the material properties. The system was analyzed using the Adams and Ansys software packages and dynamics (hand calculations). in addtion to these vaues the spring constant was found by measuring the deflection after the application of a force in compression on the spring. | + | Computer models were created of each of the following parts. Using the current model as a guide and accepted values for the material properties. The system was analyzed using the Adams and Ansys software packages and dynamics (hand calculations). in addtion to these vaues the spring constant was found by measuring the deflection after the application of a force in compression on the spring. |
| + | |||
| + | Two Engineering specifications were aniylised: Conditons for sleep and durability of the leaver arm. | ||
| + | |||
| + | The abitly of the yo-yo to sleep is primarily dependant on the centripetal force felt by the weight at the end of the leaver. this is in turn dependent upon the angular velocity of the yo-yo. This angular velocity was determined using a force analysis of the weight and leaver arm for the point at which the the brake will disengage. | ||
The stresses resulting from these forces on the lever were analyzed using ANSYS. The stresses cause bending and axial tension, both of which are a concern because either can cause failure. | The stresses resulting from these forces on the lever were analyzed using ANSYS. The stresses cause bending and axial tension, both of which are a concern because either can cause failure. | ||
Revision as of 21:05, 25 March 2007
Contents |
Description
The smart yo-yo is a yo-yo that makes it very easy to return compared to traditional yo-yos.
How It Works
The concept behind the smart yo-yo is a brake that is disengaged as long as the yo-yo is spinning fast enough. A lever is attached to the hub of the yo-yo and is allowed to pivot from one end. A small metal weight is attached to the other end. In the middle of the lever is a spring which pushes the lever into contact with the bearing. This bearing rides on the center axle and is the mounting point for the string.
At low speeds the spring force is stronger than the centripetal force acting on the weight, and the brake is engaged. This stops the rotation of the bearing with respect to the outer shell causing the yo-yo to wind up. Once the yo-yo is spinning fast enough the centripetal force of the weight overcomes the spring force and the lever moves away from the bearing, allowing the hub to spin freely so the yo-yo "sleeps." Additionally the mechanical break creates an automatic return condition where very little force is required to return the yo-yo.
In traditional yo-yos, the whole body of the yo-yo is one part and has a string wrapped around the middle. It "sleeps" by spinning on the string. Since this depends on many varying characteristics of the string, including how much friction is involved or how tight the string is tied, it is very unpredictable. However with the bearing this modle allows for longer and more reliable spin and sleep times.
Computer models were created of each of the following parts. Using the current model as a guide and accepted values for the material properties. The system was analyzed using the Adams and Ansys software packages and dynamics (hand calculations). in addtion to these vaues the spring constant was found by measuring the deflection after the application of a force in compression on the spring.
Two Engineering specifications were aniylised: Conditons for sleep and durability of the leaver arm.
The abitly of the yo-yo to sleep is primarily dependant on the centripetal force felt by the weight at the end of the leaver. this is in turn dependent upon the angular velocity of the yo-yo. This angular velocity was determined using a force analysis of the weight and leaver arm for the point at which the the brake will disengage.
The stresses resulting from these forces on the lever were analyzed using ANSYS. The stresses cause bending and axial tension, both of which are a concern because either can cause failure.
Parts
The table belows lists the Bill of Materials for the Smart Yo-yo:
| Part # | Part Name | Category # | Function | Material | Picture |
|---|---|---|---|---|---|
| 1 | Hub | Support element | Houses internal components | Plastic | File:Xx.JPG 50px |
| 2 | Lever | Transmission | Applies friction to main bearing | Plastic | File:Xx.JPG 50px |
| 3 | Main Bearing | Support Element | Allows hub and axle to rotate, attaches hub to string | Plastic | File:Xx.JPG 50px |
| 4 | Axle | Support Element | Connects the two halves of the hub and rotates in the main bearing | Steel | File:Xx.JPG 50px |
| 5 | Spring | Input | Keeps brake engaged | Steel | File:Xx.JPG 50px |
View Yo-yo in Motion
Graphical Representation of the Stress
