Kodak Waterproof One-Time-Use Camera

Revision as of 14:43, 30 July 2006

Figure 1: Fully assembled product

captions for images

Description

This product is a one-time disposable, waterproof camera manufactured by Kodak. It has 23 distinct parts with the majority being made of ABS Plastic and by injection molding.

How It Works

The disposable camera is all mechanical with no electrical components (the exception is a camera with a flash, where a circuit board and battery are included, but that is not the case in this model).

When the photographer depresses the shutter button (which is actually just an extension of the "Viewfinder"), the button moves the "Shutter Lever" to one side, rotating the "Shutter" until the "Shutter Spring" forces the "Shutter Lever" to return to a halfway position. The "Shutter" cannot be rotated again until the "Shutter Lever" is reset. The "Shutter" remains open for only a fraction of a second, as the "Shutter Spring" retracts it as soon as the "Shutter Lever" passes, allowing light to pass through both lenses to the exposed film. During the "Shutter Lever" movement, the "Camshaft" is offset slightly by an extension from the "Shutter Lever" which releases the "Film Advance Lock."

With the picture taken, the photographer winds the "Film Advance Wheel" which rolls up film into the "Film Canister" and clicks off numbers on the "Frame Counter." The film is slotted onto the "Sprocket" which is joined to the "Camshaft" causing both to rotate with the film. When the "Camshaft" rotates a complete cycle, the "Shutter Lever" is reset and the "Film Advance Lock" returns to its original position preventing operation of the "Film Advance Wheel".

The purpose of the "Exterior Front" and "Exterior Back" covers are to protect the camera from the elements. The "Outside Film Advance" allows the rotation of the "Film Advance Wheel" despite the exterior covers. The "Washer" seals the hole between the "Outside Film Advance" shaft and the "Film Advance Wheel"

The "Lens Holder" and "Eyehole Holder" serve to hold their respective components in place. The "Eyehole Cover" allows only a small fraction of the incoming light to be focused on the "Inner Lens" giving a sharper, clearer image.

Current Status

--blurb

Parts

The table belows lists the Bill of Materials for the disposable camera:

Table 4.1: Disposable Camera Bill of Materials

Part #	Part Name	# Req'd	Mat'l	Manufacturing Process	Image
1	Back Interior	1	ABS Plastic	Injection Molding
2	Back Plastic Cover	1	ABS Plastic	Injection Molding	Need to upload
3	Camshaft	1	ABS Plastic	Injection Molding
4	Eyehole for Shutter	1	ABS Plastic	Injection Molding
5	Film Advance Gear	1	ABS Plastic	Injection Molding
6	Film Advance Lock	1	ABS Plastic	Injection Molding
7	Film Canister	1	Varied	Varied
8	Film Spindle	1	ABS Plastic	Injection Molding
9	Frame Counter	1	ABS Plastic	Injection Molding
10	Front Interior	1	ABS Plastic	Injection Molding
11	Front Plastic Cover	1	ABS Plastic and Rubber	Injection Molding and Rubber
12	Inner Lens	1	ABS Plastic	Injection Molding
13	Interior Body	1	ABS Plastic	Injection Molding
14	Lens Holder	1	ABS Plastic	Injection Molding
15	Outer Lens	1	ABS Plastic	Injection Molding
16	Outside Film Advance	1	ABS Plastic	Injection Molding
17	Shutter	1	1040 Steel	Forming
18	Shutter Lever	1	ABS Plastic	Injection Molding
19	Shutter Spring	1	1040 Steel	Forming
20	Spring for Shutter Lever	1	1040 Steel	Forming
21	Sprocket	1	ABS Plastic	Injection Molding
22	Viewfinder	1	ABS Plastic	Injection Molding
23	Washer	1	Rubber	Molding

Disassembly

The ease of disassembly (ranked on a scale of 1 - 5 with five being the most difficult) is ranked at 2. No tools are required for disassembly but a flathead screwdriver or knife helps.

The following table lists the steps and procedures for disassembly:

Table 5.1: Disassembly of a Disposable Camera

Step	Procedure	Image
1	Pop film advance wheel up and out from body; separate covers	Figure 5.1: Exterior Disassembly
2	Remove film canister and film spindle	Figure 5.2: Large Component Removal
3	Remove lens holder, outer lens, shutter cap, shutter spring, shutter, eyehole, and inner lens	Figure 5.3: Lens Assembly Dissection Figure 5.4: Lens Assembly Dissection View 2
4	Remove viewfinder, frame counter, internal film advance wheel, shutter lever, advance lock, camshaft, lever spring, and sprocket	Figure 5.5: Final Component Removal

Click below for link to animated disassembly of modeled parts (not uploaded)

Disassembly of Camera

Files

3D Models

3D Models in STEP Format

3D Models in ACIS Format

3D Models in IGS Format

3D Models in STL Format

2D Drawings

2D Alibre Drawings (.AD_DRW)

2D Drawings in STP Format

Camera Assembly

Camera Assembly as ACIS, STL, STP, and Alibre

Table 6.1: List of Models for Download
(Zipped ACIS, IGS, STL, STP, AD_PRT Files)

Part #	Part Name	Image	3D Models	2D Drawings
1	Back Interior		Back Interior Cover Package	2D
2	Back Plastic Cover	Need to upload	Back Exterior Cover Package	2D
3	Camshaft		Camshaft Package	2D
4	Eyehole for Shutter		Eyehole for Shutter Package	2D
5	Film Advance Gear		Film Advance Gear Package	2D
6	Film Advance Lock		3D Packaged Models	2D Packaged Drawings
7	Film Canister		Back Interior Package	2D Packaged Drawings
8	Film Spindle		Back Interior Package	2D
9	Frame Counter		Back Interior Package	2D
10	Front Interior		Back Interior Package	2D
11	Front Plastic Cover		Back Interior Package	2D
12	Inner Lens		Back Interior Package	2D
13	Interior Body		Back Interior Package	2D
14	Lens Holder		Back Interior Package	2D
15	Outer Lens		Back Interior Package	2D
16	Outside Film Advance		Back Interior Package	2D
17	Shutter		Back Interior Package	2D
18	Shutter Lever		Back Interior Package	2D
19	Shutter Spring		Back Interior Package	2D
20	Spring for Shutter Lever		Back Interior Package	2D
21	Sprocket		Back Interior Package	2D
22	Viewfinder		Back Interior Package	2D
23	Washer		Back Interior Package	2D

Table 6.2: Point and Mesh Clouds Available for Download
(Zipped .wrp format)

Image	Link
Figure 6.1 Front Exterior Scan	zipped
Figure 6.2 Front Interior Scan	zipped
Figure 6.3 Rear Exterior Scan (Front View) Figure 6.4 Rear Exterior Scan (Back View)	zipped
Figure 6.4 Rear Interior Scan	zipped