Group 5 - Two Power Sanders

Revision as of 01:16, 7 December 2009

Ryobi Corner Sander

Battery Powered Ryobi Corner Sander

Introduction

For the MAE 277 reverse engineering project, our group was given two electric powered RYOBI corner sanders (Model #’s P400 & CFS1502). One of the sanders is powered by an electric cord and the other is battery-powered. Throughout the semester, we will be dissecting and analyzing the components that make these two products work. We will then compare the different results for the two sanders to figure out which one is more efficient than the other.

Gate 1

Work proposal

Management proposal

Product assessment

Gate 2

Causes of Corrective Action

Product Dissection Plan

Analysis

Gate 3

Component Summary

Design Revisions

Solid Modeled Assembly

Engineering Analysis

Gate 4

Assembly

RYOBI Battery-Powered Corner Sander

Step	Description	Easiness	Tools Used	Pictures
1	Place the electric motor and switch assembly into the housing so that the spindle is placed into the lube. This part is fitted into the casing. The wires should be tucked into the outer parts of the housing so they will not be pinched when it is put together.	1	Hands	Casing and Motor
2	Place the black switch in it\'s fitted housing next to the motor. Then place the yellow on/off switch over the black one.	1	Hands	Casing and Motor
3	Place the small metal clip against the yellow switch to stabalize the switch.	3	Hands	Metal Clip
4	Place the gears and bearing with counterweight into its fitted spot in the housing. The gears should be able to now spin the spindle.	1	Hands	Casing and Motor
5	Place the two white connectors into the housing. The smaller one fits in below the switch assembly. If looking at the sander with the motor to the top right, the larger connector will be placed about an inch to the left of the gears in it\'s fitted spot.	1	Hands	Casing and Motor
6	Slide the other casing onto the casing with the motor, gears, and switch assembly. It should match up so that connectors go into their fitted spots. The connectors should now be seen on the botton of the sander.	2	Hands	Casing and Motor
7	There are eleven Phillips head #2 screws that need to be screwed onto the outer casing. There are designated holes for the screws, and they are the only holes on the sander.	2	Phillips head #2 screw-driver	Casing and Motor
8	This is the orange piece that can be taken out by hand. It is located along the handle next to the rubber grip	1	Hands	Casing and Motor
9	Snap the velcro pad housing onto the bottom of the sander. It snaps on using the connectors.	1	Hands	Casing and Motor
10	There are five phillips head #2 screws that need to screw the sand-paper velcro pad onto the sander.	2	Phillips head #2 screw-driver	Casing and Motor

RYOBI Corner Sander

Step	Description	Easiness	Tools Used	Pictures
1	Slide the field assembly over the armature assembly. The wires for the switch should be on the opposite side of the vacuum fan as seen in the picture.	1	Hands	Casing and Motor
2	Attach the switch to the field assembly. This is done by connecting it to the fitted connector of the red wire.	1	Hands	Casing and Motor
3	Connect the black wire coming from the power supply cord to the switch.	1	Hands	Casing and Motor
4	Place one brush into the connector coming from the white cord of the power supply. Place the other brush into the connector coming from the black cord of the field assembly.	1	Hands	Casing and Motor
5	Everything assembled thus far will fit onto the casing. The field assembly has a fitted spot in the center of the casing, everything else attached will fall into it\'s fitted spot.	1	Hands	Casing and Motor
6	The orange on/off switch lays in next to the switch assembly	1	Hands	Casing and Motor
7	The black fan baffle fits in over the sand vacuum. The curved edges will fit onto the housing properly.	1	Hands	Casing and Motor
8	Place the two white connectors into the housing. The smaller one fits in below the switch assembly. If looking at the sander with the motor to the top right, the larger connector will be placed about an half an inch to the left of the field assembly in it\'s fitted spot.	1	Hands	Casing and Motor
9	Place the second part of the housing onto the connectors. Wires must be placed in designated areas. There are teeth that will catch the wires to keep them in place.	4	Hands	Casing and Motor
10	Screw the two cord clamp screws over the cord where it meets the sander.	2	Phillips Head #2 screw-driver	Casing and Motor
11	Screw in both of the external screws to connect both casings. These screws are located underneath where the grip will be.	2	Phillips Head #2 screw-driver	Casing and Motor
12	Place the grip on top of the sander. Fasten the three top cover screws.	2	Phillips Head #2 screw-driver	Casing and Motor
13	Place the velcro pad housing onto the bottom of the sander and use the 4 velcro pad housing screws to fasten it.	2	Phillips Head #2 screw-driver	Casing and Motor
14	Place the velcro pad onto the velcro pad housing and use 5 of the velcro pad housing screws to fasten it onto the velcro pad housing.	2	Phillips Head #2 screw-driver	Casing and Motor
15	Fit the vacuum bag over the vacuum exhaust coming out the back of the sander as seen in the picture.	1	Hands	Casing and Motor

References

Ryobi Corner Cat Power Sander Parts (model #CFS1502)