Group 36 - Ryobi Contractor's Saw

Executive Summary

This section is much like an abstract and summarizes the entire report

Introduction

This section should include an introduction of the product and a brief description of group members (i.e. who was responsible for which sections or tasks)

Before Disassembly Section

General notes about the product (it's condition, how it works, how many parts, types of materials, etc)

Disassembly Procedure

• Document each step to disassemble the product
• How difficult was each disassembly step?
• What types of tools were required to perform this step?
• Include a picture of each disassembly step

After Disassembly

Disassembly Process Table

Part #	Component Name	Number of Parts of This Type	Material(s)	Manufacturing Process	Image
1	Motor Housing	1	Plastic, Brass, Galvanized Steel	Injection Molded, Die Cast and Machined, Stamped	PUT PICTURE HERE
2	Stator	1	Plastic, Copper, Magnetic Alloy	Injection Molded, Extruded, Stamped and Soldered	PUT PICTURE HERE
3	Trigger and Safety Switch	1	Plastic, Aluminum	Injection Molded, Extruded and Machined	PUT PICTURE HERE
4	Power Cord	1	Copper, Plastic	Both Extruded	PUT PICTURE HERE
5	Upper Guard	1	Aluminum, Brass	Die Cast and Machined, Machined	PUT PICTURE HERE
6	Reduction Gear	1	Steel	Extruded and Machined. Also dipped in an anti-corrosion coating.	PUT PICTURE HERE
7	Central Washer	2	Steel	Die Cast	PUT PICTURE HERE
8	Depth Adjustment Lever	1	Plastic	Injection Molded	PUT PICTURE HERE
9	Rubber Stopper	1	Rubber	Injection Molded and Vulcanized	PUT PICTURE HERE
10	Handle	2	Plastic	Injection Molded	PUT PICTURE HERE
11	Rotor	1	Steel, Copper, Plastic	Stamped, Extruded and Machined, Extruded, and Injection Molded	PUT PICTURE HERE
12	Vent Cover	1	Plastic	Injection Molded	PUT PICTURE HERE
13	Lower Guard	1	Aluminum	Die Cast	PUT PICTURE HERE
14	Carbon Brush	2	Plastic, Copper, Carbon, Brass	Injection Molded, Extruded, Machined, Stamped	PUT PICTURE HERE
15	Lower Guard Lift Lever	1	Plastic	Injection Molded	PUT PICTURE HERE
16	Long Screw	6	Steel	Extruded and Machined	PUT PICTURE HERE
17	Medium Screws	8	Steel	Extruded and Machined	PUT PICTURE HERE
18	Short Screws	4	Steel	Extruded and Machined	PUT PICTURE HERE
19	Central Bolt	1	Steel	Extruded and Machined	PUT PICTURE HERE
20	Long Spring	1	Steel	Extruded	PUT PICTURE HERE
21	O-Spring	1	Steel	Extruded	PUT PICTURE HERE
21	C-Clip	1	Steel	Stamped	PUT PICTURE HERE
22	Large Gauge Screw	1	Steel	Extruded and Machined	PUT PICTURE HERE

• Part number
• Part name
• Number of parts of this type
• Part material
• Part manufacturing process
• Image of the part
• CAD file for selected parts

Assembly

• Document each step to reassemble the product
• How difficult was each assembly step?
• What types of tools were required to perform this step?

After Assembly

• Does it still work?
• Conclusion remarks

References

APA Style You must use this format (It's easier than MLA, so don't worry).

Guide to Writing Wiki Code

The beauty about Wiki is that if you don't know the code, you can steal it from someone's page that does. Feel free to click the "edit" links or tabs to view the code for sections or the pages respectively. Be weary about wrecking havoc on another's page. Each page can be rollbacked to a previous verison and your username is linked to all changes. Although you might think it's cool to go through and insert "MIKE RULES" throughout the page, I'm sure Dr. Lewis would not be pleased.

Here's a few tips on writing with Wiki:

This is a bracket "[" "]"

This is a brace "{" "}"

To create a new page/link within Wiki:

• Double brackets, page name, double brackets
• Typing in a new page name will automatically create a page, which when clicked, you can then edit.
• Whatever name you first type in is the name of the page. You can't change page names, only create new pages. Think before you create a new page.
• Don't worry about slashes or anything, all pages are located in the same directory. If I wanted to create a page called "MAE 277 Template" the code would be ''MAE 277 Template'' Note: Brackets are italicized to prevent creating a new page.

Your table of contents is created automatically.

• 1,2,3,4 are level 2 sections
• 1.1, 1.2, 1.3 are level 3 headers

To create headers:

• Section titles are wrapped with two equal signs ==My favorite header==
• Bold headers within a section are wrapped with three equal signs ===My not-so-favorite header===

Asterisks indicate bullets. Be sure to put each asterisk on a new line.

• Here's one
• Here's two *Here's three, but its not on the next line

Bold text:

• Start line with "b" in "<>". Be sure to end the line with "/b" in "<>" if you don't want the whole paragraph to be bold.
• Surround text to be bolded with three " ' " marks on either side. Or highlight the text and click the "B" button on the toolbar.

Italics:

• "i" in "<>". Don't forget to end with "/i" in "<>"
• Highlight the text and click the "I" button in the toolbar (It will put four " ' " on either side).

This is a broken link media file caption

Media tags are indicated by "Media:", images by "Image:" Broken links in red. Case is not important. Use the toolbar to get examples if you're not sure.

Spacing is werid in wiki. Single return does nothing.

Double return (blank line), breaks the line.

Triple return (two blank lines), puts an extra blank line between lines of text.

"br" in "<>" will break lines. They can also be used to separate section headers.

Finally, use the "Show Preview" button on the bottom of the page to see how it looks before saving. It will allow you to catch and edit your errors without having to edit the page again. Just don't forget to save it when you're really done.