Group 36 - Ryobi Contractor's Saw

Revision as of 12:09, 8 December 2007

Executive Summary

For this project, our group was instructed to examine the Skilsaw contractor's saw. We first disassembled the saw, and analyzed its components. We then made recommendations for design improvements, before reassembling it.

Introduction

The Skilsaw circular saw is primarily designed for cutting wood, but with a change of blades can also cut through other materials, such as metal piping. This hand-held saw is powered by an AC current, which is converted to mechanical energy in the rotation of the blade. The electrical engine has a power output of 2.3 HP, and spins at 4,600 RPM. During this project, the group disassembled, analyzed, and reassembled the saw.

Group Members

Rita Groetz acted as the group leader. She was responsible for scheduling meeting times, keeping the entire group up to date on the project with emails and phone calls. She also was the photographer for the group, and the primary contributor and editor for the CIBER-U web page.

Kevin Bush was responsible for assembling and disassembling the saw. He had prior experience with both the materials and mechanics of the saw; knowledge which was invaluable to the group. He also contributed to the CAD design, and presented the project.

David Pohl was the primary CAD designer. He created the majority of the CAD drawings, and also created an animated movie clip, using those drawings to illustrate how the motor looked on the inside, as it was running. He also took notes during most meetings, and presented the project.

Kevin Ho contributed to the power point presentation and contributed to the CIBER-U web page.

Tai Nguyen took notes for the disassembly process, contributed to the power point presentation, and contributed to the CIBER-U web page.

All group members collaborated on analyzing the components of the saw.

Before Disassembly Section

Since the saw was brand new when given to the group, we assumed that its initial appearance and operation was correct. Apart from basic outer components, like housing and a handle, the saw contained a safety switch, a movable foot, and a detachable wrench to tighten the center bolt.

The saw is operated by engaging a safety switch, and then a power switch. It was very loud, and even without the torque of the blade, kicked back when it was initially operated. This demonstrated the physical power of the motor.

The group estimated that the saw would contain about 40 components, and predicted that those components would be made of plastic, steel, aluminum and copper.

Disassembly Procedure

1. Took out Wrench with hands

2. Remove rubber stopper with T-30 torx bit

3. Remove lower guard lift with T-20 torx bit

4. Remove spring from lower guard with needle nose pliers

5. Removed blade-holding bolt and “washers” with 13mm socket

6. Removed spring ring with swiss army knife

7. Removed C-clip and depth adjustment lever with pliers and a 12mm wrench

8. Removed lower guard with hands

9. Removed 3 short screws with T-20 screw driver and bearing flange

10.Removed pinion shaft

11.Removed 4 long screws from upper gaurd with a T-20 torx screwdriver

12.Removed upper guard with hands

13.Removed armature with hands

14.Removed plain washer and 2 washers from the armature

15.Removed 6 screws to take handle apart with T-20 torx screwdriver

16.Pulled the handle off with hands

17.Removed 2 medium screws and pulled off housing cover with hands

18.Slid out motor brushes with needle nose pliers

19.Took apart brushes with hands

20.Removed 2 long screws from stator

The disassembly was relatively easy except for pulling off the C-Clip, which needed to be slowly worked out of its former position.

After Disassembly

Component List

Part #	Component Name	Number of Parts of This Type	Material(s)	Manufacturing Process	Image
1	Motor Housing	1	Plastic, Brass, Galvanized Steel	Injection Molded, Die Cast and Machined, Stamped
2	Stator	1	Plastic, Copper, Magnetic Alloy	Injection Molded, Extruded, Stamped and Soldered
3	Trigger and Safety Switch	1	Plastic, Aluminum	Injection Molded, Extruded and Machined
4	Power Cord	1	Copper, Plastic	Both Extruded
5	Upper Guard	1	Aluminum, Brass	Die Cast and Machined, Machined
6	Pinion Shaft	1	Steel	Extruded and Machined. Also dipped in an anti-corrosion coating.
7	Central Washer	2	Steel	Die Cast
8	Depth Adjustment Lever	1	Plastic	Injection Molded
9	Rubber Stopper	1	Rubber	Injection Molded and Vulcanized
10	Handle	2	Plastic	Injection Molded
11	Rotor	1	Steel, Copper, Plastic	Stamped, Extruded and Machined, Extruded, and Injection Molded
12	Vent Cover	1	Plastic	Injection Molded
13	Lower Guard	1	Aluminum	Die Cast
14	Carbon Brush	2	Plastic, Copper, Carbon, Brass	Injection Molded, Extruded, Machined, Stamped
15	Lower Guard Lift Lever	1	Plastic	Injection Molded
16	Long Screw	6	Steel	Extruded and Machined
17	Medium Screws	8	Steel	Extruded and Machined
18	Short Screws	4	Steel	Extruded and Machined
19	Central Bolt	1	Steel	Extruded and Machined
20	Long Spring	1	Steel	Extruded
21	O-Spring	1	Steel	Extruded
21	C-Clip	1	Steel	Stamped
22	Large Gauge Screw	1	Steel	Extruded and Machined
23	Wing Nut Bolt	1	Steel	Extruded and Machined
24	Wing Nut	1	Steel	Stamped
25	Wrench	1	Galvanized Steel	Stamped
26	Plain Washer	1	Aluminum	Stamped
27	Washer	1	Aluminum	Stamped
28	Bearing Flange	1	Steel	Machined
29	Depth Adjustment Nut	1	Steel	Machined

CAD Drawings

Bearing Flange

Pinion Shaft

Rotor

Upper Guard

Assembled Parts

We also produced a video clip, using the CAD drawings. It can be viewed here.

Design Changes

While the long, medium, and short screws all took the same size bit and had the same thread, the large screw took a different bit. This group suggests that the large screw be changed to accommodate the same size bit as the others.

Also, the carbon brushes are simply set into the saw and held in place by the vent. The group suggests that the brushes are fastened in place independently.

Assembly

1. Placed rotor and motor back in housing cover.

2. screw in the two screw back in stator.

3. placed screw back in housing.

4. placed handle back together with wires back inside.

5. Placed screws back in with T-20 torx screw driver.

6. Placed plain washer and 2 washers to the armature.

7. Placed armature back on.

8. Placed upper guard back on by hands.

9. Placed 4 screws back on upper guard with a T-20 torx screw driver.

10. Place pinion shaft back on.

11. Placed 3 short screw with T-20 screw driver back on.

12. Place lower guard back on.

13. Placed C-clip and depth adjustment lever with pliers and a 12mm wrench back on.

14. Place spring back on by hand

15. Placed blade-holding bolt and washers with 13mm socket back on.

16. Placed spring from lower guard with tweezer (difficult)

17. Placed lower guard lift with T-20 torx bit

18. Placed rubber stopper with T-30 torx bit

19. Placed wrench by hands back on.

After Assembly

Reassembly

Upon reassembling the saw, the group successfully tested it. It ran almost exactly as it had before, but once the switch was disengaged, the motor continued to spin from its momentum. The group surmised that the broken copper wiring in the carbon brushes must have had something to do with the braking of the motor. This problem could be quite dangerous if the lower guard malfunctioned.

Design Problems/ Changes

The group discovered that there was a lot of plastic used in the saw's construction. We felt that there was not enough metal at pivotal load-bearing locations on the saw. Instead, we found plastic at these locations. The high power of the drill and the brittle nature of the plastic could lead to a dangerous malfunction, were some of the plastic supports to break. We suggest that high-load areas be reinforced with some sort of steel.

We also noticed that there were no ball bearings on the bushings. Instead, the bushings were heavily lubricated with grease. If the lubricant was burned away by regular use, there could be a large amount of friction created, efficiently "burning out" the motor. We suggest that to increase the longevity of the saw, ball bearings are added to the bushings.

References

Product Detail - 7 1/4" Skilsaw - Model #5400-01. (n.d.). Retrieved December 3, 2007, from http://www.skiltools.com/en/AllTools/Category/Product/default.htm?pid=5400-01&cid=192160