Group 1 2012 Gate 4

Revision as of 22:25, 29 November 2012

Blabbity blab blab we put the piano back together an' shit.

Project Management

Cause for Corrective Action

The decision to decentralize the work involved in completing Gate 3 by assigning each group member a specific task and having no group meetings proved to be highly effective in minimizing the total amount of time spent on the project while still providing an acceptable degree of quality. Given the fractured and busied nature of everyone in the group's schedule during this project gate, we will continue to use this method to complete Gate 4.

Product Explanation

Product Reassembly

In the end we need to answer these: How difficult is each step? How can you define a meaningful scale to rate the difficulty? How was the product originally assembled (by hand, robot, etc.)? Is the assembly the same as the disassembly?

#	Step Description	Tool Used	Difficulty Rating	Image
1	Put sustain pedal bar in	None	1
Place the sustain bar axles into their respective hinges, and temporarily remove the mutes covering the screw holes before attaching.
2	Rescrew the hinges of the sustain pedal bar	Screwdriver	2
Realign the hinges over the screw holes and tighten screws to fasten down the sustain bar.
3	Rescrew the mutes above the hinges of the sustain pedal bar	Screwdriver	4
Reattach the temporarily removed mutes over the hinge holes to complete the mute assembly.
4	Rescrew the iron bracket back on to the end of the action	Screwdriver	2
First, make sure that the felt pads are around the holes, then screw on the iron bracket to the action frame.
5	Replace spring bar	Screwdriver	7
Slide the spring bar back in between the hammer and mute assemblies, then mount it to the rest of the action via the four screws. After attaching the spring bar, carefully realign the springs into their respective slots on the base of each hammer, and be sure not to cross any.
6	Replace the una corda pedal bar	None	2
Before screwing on the hinges to the una corda pedal bar, ensure that the axes are correctly seated to that they will fit into the cutouts in the action. Then proceed with inserting the screws through the holes in the hinges and tightening them down.
7	Replace removed mute	Screwdriver	1
With the mute pivot at an angle, fasten it to the mute assembly with the swivel screw, then turn it into place, ensuring it connects with the mutes and lines up with the respective holes.
8	Reattach hammer	Screwdriver	1
Replace removed hammer assembly
9	Reattach pull-rod to associated lever.	Screwdriver	1
Reattach the pull rod and lever to the action frame, then reconnect it to the respective hammer using the leather strap.
10	Place back in action bracket and rescrew it.	Screwdriver	5
Replace the action by lining up the action brackets with the threaded holes in the piano frame and replace each screw. Note that there are four holes, and that the action may take some maneuvering/forcing to be properly repositioned inside the piano.
11	Replace key pin board	None	3
Place the key pin board into the front of the piano frame and reinsert the screws down its length, and secure it to the frame. Note that before the key pin board can be reattached, all of the pull rods from the action must be pointing up instead of hanging down. We used the horizontal bar that secures the keys to lift up all the pull rods at once.
12	Replace keys	None	15
Ensuring the correct order, put the keys onto the right pins, and ensure that they pivot easily. Note that we simultaneously replaced each key and attached its pull rod.
13	Replace the steel pull-rods on the key-levers	None
Reattach the correct pull rods with their respective key on the key pin board. Take care to ensure each pull rod is connected to its correct key. They can cross, and this will disrupt playing.
14	Replace pedal hinges and put axle back on to pedal	Screwdriver	5
Put the pedal axle through the pedals and the pedal hinges before screwing them into the floor of the piano frame.
15	Reattach pedal levers to piano floor	Screwdriver	2
Line up the pedal levers with the holes in the piano frame floor then screw them back into place.
16	Replace pedal dowels	None	1
Simply attach the pedal dowels to the pedal levers using the metal pin protruding from the end and place the tops under the mute and una corda bars.
17	Reconnect pedal levers to pedals	None	3
Reattach the pedal levers to the pedals using the nuts and threaded rods.Be sure to test the una corda pedal and make sure it does not completely stifle the piano.
18	Replace the horizontal bar on top of keys	Screwdriver	1
This bar holds the keys in place, so ensure it is tightened down so that they stay in place, but are still able to pivot smoothly.
19	Replace keyboard cover	Screwdriver	2
Reattach the keyboard cover to the sliding hinges via screws.
20	Replace horizontal bar on top of sliding keyboard cover	Screwdriver	1
Reattach the bar by using the respective screws and ensure that the sliding cover can rest upon it.
21	Replace bottom baseboard	None	1
Simply place the baseboard into the front of the piano and twist the latch to lock it closed.
22	Replace top hatch	Screwdriver	2
First, screw on the hinges attaching the top hatch to the rest of the piano frame and close the hatch.

Mechanisms

The majority of motion in a piano relies on interconnected levers to transmit energy or control to the strings. However, the initially simple motions of each individual part interact to create a very controllable set of movements necessary for piano playing. In the action and elsewhere, there are push rods and pull rods that effectively create our-bar mechanisms.

Hammer Movement

• Modified four-bar linkage
• The slow, short range-of-motion movement of keys translates to fast, wider-angle movement of the hammer. Then the linkage collapses and allows the hammer to retract.
• The key is connected to a central lever in the action. The lever has a push rod that acts as a couple to the hammer bar. The hammer bar is also a lever that amplifies motion. The push bar falls out of place at the top of the key's motion and allows the hammer to return under gravity.
• Fuck math. I'll get that in a bit …

For the four-bar linkage to model the hammer movement, the contact point between the top of the push rod and the hammer body must be idealized as an axle pivot.

"Your group must identify one or more mechanisms that your device uses to generate specific motion, control system behavior, modify/condition energy, etc"

They say we only need one. I don't believe them.

First Mechanism

• Technical Name
• Purpose
• "how the mechanism works"
• Equations governing the design of the mechanism

Design Revisions

Based on our analysis of the piano so far, and our understanding of the GSEE factors, three different revisions to the traditional piano could be made that would beneficially modify its design on the system level.

Half-Size Piano

One of the issues with the piano is that it is too large and heavy. This limits its mobility, as well as places where it can be used. A solution to this would to reduce the number of keys in the piano itself. By cutting the number of keys in half, this would greatly reduce the size of the piano and its overall weight. This would increase its overall mobility, and its smaller footprint would allow the piano to be placed in more locations. Taking note of societal factors, the keys that would be eliminated would be those at the two extremes of the note range. This would make sure that the piano could still play a large number of piano compositions, that hover around the notes near middle C.

Multiple Frames

A second possible revision that would reduce the vertical profile of the piano at the expense of weight would be to divide the current frame system into two or perhaps three parts, and stack them on top of each other. This compact width would allow the piano frame to be oriented in a plane parallel to the keys. The piano can still be played with one action assembly because of the variation in string height. This reconfiguration would allow for a desktop version of piano.

Chord Keys

Another issue with the full size piano is that it is difficult for children and people with small hands to extend their fingers far enough to consistently play certain chords. The solution for this would be to integrate auxiliary keys to the original piano set up, that would hit the notes of the chord with a single depressed key. This takes into account societal factors by increasing the number of people that can learn to play the piano, even before they have grown to the ideal playing size, or if they never will. This modification would also allow for greater musical experimentation, as a greater number of notes can now be played simultaneously.