Group 11 - Dual Stage Snow Thrower (Gasoline Powered) - Gate 4

Revision as of 15:25, 30 November 2012

Intro

In this stage, we reassemble the machine, examine the most crucial mechanism, and propose some possible design revisions to the machine.

Final Critical Review

Product Reassembly

Mechanisms

1. Spur gear: It is the simplest type of gear. It consists of a cylinder with the teeth projecting radially, and although they are not straight-sided in form, the edge of each tooth is straight and aligned parallel to the axis of rotation. The single spur gear is used to make the whole gear system more stable.
Specs:
Number of teeth=13
Module =2.33
Face width= 18 mm
Diameter of outside circle= 35 mm

2. Bevel Gear: It is specifically crow gear. Crown gear is a particular form of bevel gear whose teeth project at right angles to the plane of the wheel; in their orientation the teeth resemble the points on a crown. This crown gear is meshing with spur gears. Then the crow gear interacts with the two spur gears.

Number of teeth = 26

3. Worm Gear: A worm gear is sharing the same axle with the spur gear; the spur gear rotates with the bevel gear and rotates the worm gear. They have the same angle velocity. Worm gear motivates the discharge chute to direct the snow's outlet.

Possible Design Revisions
(Note: As previously stated, the title is misleading. The Toro CCR-2000 is a single-stage blower.)

1: Wider intake scoop. This would require a longer auger, a wider upper shroud, and a smaller reduction ratio on the pulley.
Global factors: The blower would be able to handle more snow at a time<.br /> Societal factors: Its improved capacity means it takes even less time and effort to clear the same area. That is less time for the operator to spend outside in the freezing cold.
Economic factors: By having to go back and forth less times while running the engine, this revision saves time, money, fuel, and maintenance needs, making the machine pay for itself sooner.
Environmental factors: Less time spent in operation means less overall pollution from the combustion engine.

2: Add an icebreaker auger, making it a dual-stage. The second auger will be larger, but will rotate much more slowly. It will also be made of steel, with blades to loosen up the snow and break apart ice. It will require a more powerful engine, an additional axle and pulley system, and a metal intake shroud to efficiently support the weight.
Global factors: The blower will become a heavy duty machine instead of a light duty one.
Societal factors: This revision would make the blower ideal for areas with heavy snowfall or icing problems.
Economic factors: It will be more expensive in materials and fuel, since there would be a good amount of metal to be machined and added to the blower. Metal is much more expensive than ABS plastic, and the extra weight would tax the engine more.
Environmental factors: Because of the need for a more powerful engine, it will burn more fuel at a time. However, it will burn less overall compared to using a light duty machine for heavy duty work.

3: Change to a 2-cylinder engine. This may require an enlarged chassis and a larger capacity fuel tank.
Global factors: The blower would be capable of operating faster and more consistently. It would also be capable of dealing with heavier loads, though not as heavy as a Dual-Stage blower.
Societal factors: A more powerful engine keeps the operator warmer and completes the job faster. Some users also like to show off or brag about a more powerful engine.
Economic factors: The machine will cost more, and use more fuel at a time.
Environmental factors: A 2-cylinder engine burns more fuel at a time than a single-cylinder engine. This revision will increase pollution from exhaust gases.

Procedure

Difficulty scale
1: Simple and quick. One person could do it in 5 minutes at most.
2: Complicated or tedious. The step is a little tricky or takes a long time.
3: Complicated and tedious. Two people are required for the task and the process takes time to complete.

Step	Difficulty	Tools Used	Actions
Step 1	2	13mm socket and socket wrench	Reattach upper handle to lower handle. The difficulty in this step is mainly caused by the unwieldy nature of the mostly-disassembled snow thrower.
Step 2	1	11mm socket and socket wrench	Bolt center of left side panel to frame.
Step 3	1	By hand	Return pulley belt to proper position as shown on diagram on inside of right panel cover.
Step 4	1	11mm socket and socket wrench	Reattach right side panel to frame.
Step 5	1	10mm socket and socket wrench	Reattach engine cover to engine assembly.
Step 6	2	½” socket, socket wrench, and ½” combination wrench	Reattach the remainder of the left side panel to the frame.
Step 7	3	11mm socket, 14mm socket, socket wrench, and pliers	Reassemble pulley assembly per drawing on interior of right side panel cover.
Step 8	2	by hand	Replace bottom flap between frame and lower discharge assembly. It is somewhat difficult to line up the holes in the flap with the holes in the frame and the lower discharge assembly, particularly since the flap has three extraneous holes. Upon inspection, it is obvious where the flap belongs; however, holding it in place while sliding bolts through the holes is a two-person operation.
Step 9	3	11mm socket, socket wrench, and pliers	Reattach lower discharge assembly to frame, right side panel, and left side panel.
Step 10	3	12mm socket, socket wrench, hammer, and pliers	Reattach recoil support to engine assembly. It does not fit easily back into its slot. The necessity of the hammer and the use of pliers in concert with the socket wrench cause this to be a difficult task.
Step 11	1	10mm socket and socket wrench	Reattach left side panel to frame.
Step 12	1	by hand	Replace fuel tank in proper position. Mechanically, this is a simple step so long as care is taken not to twist the fuel line. However its orientation is not completely intuitive and requires looking at disassembly pictures.
Step 13	2	11mm socket, 14mm socket, socket wrench, 11mm nutdriver, and pliers	Secure fuel tank to recoil support. This requires some awkward angles. Rusty nuts and bolts necessitate the use of tools on both the bolt side and the nut side.
Step 14	1	by hand	Reattach the spark plug cover to the spark plug.