Group6 - Revision history

GPS-6 at 21:08, 3 March 2008

2008-03-03T21:08:54Z

GPS-6 at 21:08, 3 March 2008

2008-03-03T21:08:44Z

GPS-6 at 21:08, 3 March 2008

2008-03-03T21:08:27Z

GPS-6 at 21:08, 3 March 2008

2008-03-03T21:08:00Z

GPS-6 at 21:07, 3 March 2008

2008-03-03T21:07:24Z

GPS-6 at 21:07, 3 March 2008

2008-03-03T21:07:12Z

GPS-6 at 21:06, 3 March 2008

2008-03-03T21:06:59Z

GPS-6 at 21:06, 3 March 2008

2008-03-03T21:06:40Z

GPS-6 at 19:41, 3 March 2008

2008-03-03T19:41:25Z

GPS-6 at 19:40, 3 March 2008

2008-03-03T19:40:43Z

← Older revision		Revision as of 21:08, 3 March 2008
Line 1:		Line 1:
−	<br><br>[[Image:GPSunit.jpg\|~~left~~\|300px\|GPS Unit]]	+	<br><br>[[Image:GPSunit.jpg\|right\|300px\|GPS Unit]]

	==Executive Summary==		==Executive Summary==

← Older revision		Revision as of 21:08, 3 March 2008
Line 1:		Line 1:
−	<br><br>[[Image:GPSunit.jpg\|~~center~~\|300px\|GPS Unit]]	+	<br><br>[[Image:GPSunit.jpg\|left\|300px\|GPS Unit]]

	==Executive Summary==		==Executive Summary==

← Older revision		Revision as of 21:08, 3 March 2008
Line 1:		Line 1:
−	<br><br>[[Image:GPSunit.jpg\|center\|~~150px~~\|GPS Unit]]	+	<br><br>[[Image:GPSunit.jpg\|center\|300px\|GPS Unit]]

	==Executive Summary==		==Executive Summary==

← Older revision		Revision as of 21:08, 3 March 2008
Line 1:		Line 1:
	<br><br>[[Image:GPSunit.jpg\|center\|150px\|GPS Unit]]		<br><br>[[Image:GPSunit.jpg\|center\|150px\|GPS Unit]]
−
−
−
−

	==Executive Summary==		==Executive Summary==

← Older revision		Revision as of 21:07, 3 March 2008
Line 1:		Line 1:
−	<br><br>[[Image:GPSunit.jpg\|center~~\|thumb~~\|150px\|GPS Unit]]	+	<br><br>[[Image:GPSunit.jpg\|center\|150px\|GPS Unit]]

← Older revision		Revision as of 21:06, 3 March 2008
Line 1:		Line 1:
−	<br><br><br><br><br>[[Image:GPSunit.jpg\|~~left~~\|thumb\|150px\|GPS Unit]]	+	<br><br><br><br><br>[[Image:GPSunit.jpg\|center\|thumb\|150px\|GPS Unit]]

@@ Line 90: / Line 90: @@
 <br>
 *The Assembly of the GPR is simple to complete.  If the components begin disassembled like they are at the end of the Diassembly section, assembly can be accomplished by following the steps from that section, in reverse.  The first step is to connect the LCD screen to the Motherboard.  These two pieces slide and snap into place with the use of the hands.  The step is simple and takes only a few seconds to complete.  Set this piece aside and continue.<br>Brian Stouffer<br><br>
-*Now take the Front Encasement and the Rubber Gasket/Buttons and place them together.  There are no connectors that hold these two pieces together.  They simple fit tightly to one another by a rubber design that matches the plastic perfectly.  Lay the aparatus facedown to prepare for motherboard attachment.<br>Brian Stouffer<br><br>
+*Now take the Front Encasement and the Rubber Gasket/Buttons and place them together.  There are no connectors that hold these two pieces together.  They simply fit tightly to one another by a rubber design that matches the plastic perfectly.  Lay the aparatus facedown to prepare for motherboard attachment.<br>Brian Stouffer<br><br>
 *Once you have completed step one and two of the assembly, the two pieces that you've created are ready to be attached to one another.  With the encasement and gasket facedown, place the Motherboard and LCD Screen on top, making sure to match the LCD to the clear plastic section of the encasement and the buttons to the button sensors.  You will know that these are in place when the two sets of screw holes are alligned.  There are two screws that need to be screwed into place to hold these two sections together.  You will need a small screw driver to accomplish this.<br>Brian Stouffer<br><br>
 *After screwing the motherboard back into the front encasement, the three multiple wire connections need to be reconnected.  This step is easily done without the use of any tools, but must be done with some care since it does have to deal with the unprotected hardware of the GPS unit.  These connections simply clip into place when a slight force or push is applied.<br>James Therrien<br><br>