Black and Decker Dustbuster
From GICLWiki
(Difference between revisions)
ThomasCleere (Talk | contribs) (→Parts) |
ThomasCleere (Talk | contribs) (→Parts) |
||
| Line 5: | Line 5: | ||
{| border="1" align="center" | {| border="1" align="center" | ||
|+ '''Table 1: Black and Decker Dustbuster Bill of Materials''' | |+ '''Table 1: Black and Decker Dustbuster Bill of Materials''' | ||
| − | ! width="50"|Part # !! width="100"|Part Name !! width="50"| Category !! width="120"|Function!! width="145"| Material !! width="100"|Picture | + | ! width="50"|Part # !! width="100"|Part Name !! width="50"|Category !! width="120"|Function!! width="145"| Material !! width="100"|Picture |
|- | |- | ||
! 1 | ! 1 | ||
| Line 11: | Line 11: | ||
| align="center"|Input | | align="center"|Input | ||
| align="center"|Powers the vacuum | | align="center"|Powers the vacuum | ||
| − | | align="center"|8 Recyclable Rechargable Nickel Cadmium batteries with wire and metal connections | + | | align="center"|8 Recyclable Rechargable Nickel Cadmium batteries with wire and metal connections. |
| [[Image:badbottomdiskholder.JPG |center|thumb|50px]] | | [[Image:badbottomdiskholder.JPG |center|thumb|50px]] | ||
|- | |- | ||
| Line 17: | Line 17: | ||
|align="center"|Impeller | |align="center"|Impeller | ||
| align="center"|Output | | align="center"|Output | ||
| − | |align="center"|Creates suction for the vacuum | + | |align="center"|Creates suction for the vacuum. |
| align="center"|Plastic | | align="center"|Plastic | ||
| align="center"|[[Image:badscrews.JPG|center|thumb|50px]] | | align="center"|[[Image:badscrews.JPG|center|thumb|50px]] | ||
|- | |- | ||
! 3 | ! 3 | ||
| − | |align="center"| | + | |align="center"|Motor with Fan |
| − | | align="center"| | + | | align="center"|Input |
| − | | align="center"| | + | | align="center"|Motor spins the impeller while the spinning fan pulls heat from the motor. |
| − | | align="center"| | + | | align="center"|Steel outer shell with a plastic fan and coils of copper wires |
| − | + | ||
| − | + | ||
| [[Image:badtopdiskholder.JPG |center|thumb|50px]] | | [[Image:badtopdiskholder.JPG |center|thumb|50px]] | ||
|- | |- | ||
Revision as of 12:27, 28 January 2008
Parts
Listed below is the Bill of Materials for the Black and Decker Dustbuster:
| Part # | Part Name | Category | Function | Material | Picture |
|---|---|---|---|---|---|
| 1 | Battery Pack | Input | Powers the vacuum | 8 Recyclable Rechargable Nickel Cadmium batteries with wire and metal connections. |  |
| 2 | Impeller | Output | Creates suction for the vacuum. | Plastic |  |
| 3 | Motor with Fan | Input | Motor spins the impeller while the spinning fan pulls heat from the motor. | Steel outer shell with a plastic fan and coils of copper wires |  |
| 4 | Bail Spring | Support Elements | Applies force against the Bail when engaged. | Metal/Plastic |  |
| 5 | Bail Lever | Motion Conversion Element | Unlocks spindle from gearbox. | Metal |  |
| 6 | Plastic Casings | Structural | To add a shine to the appearance of the reel. | Plastic |  |
| 7 | Spindle Housing | Structural/ Motion Conversion Element | Protects drive shaft and spins the bail. | Plastic |  |
| 8 | Power wheel/gear | Transmission | Transfers power from handle to drive shaft and scotch yoke. | Metal |  |
| 9 | Handle | Input | Applies external force to power wheel. | Plastic |  |
| 10 | Yoke Shaft | Support Element | Moves spindle up and down. | Metal |  |
| 11 | Clutch | Transmission | Stops spindle from rotating in on direction when engaged. | Metal | |
| 12 | Drive Shaft | Motion Conversion/Support Element | Transfers energy from power wheel to spin spindle. | Metal |  |
| 13 | Scotch Yoke | Transmission | Converts angular energy from power wheel to move the spindle linearly. | Metal |  |
| 14 | Screws | Structural | Holds Parts Together | Metal | |
| 15 | Mechanism Casing | Structural | Outer shell, protects mechanisms, attaches reel to rod. | Plastic | |
