Difference between revisions of "HP Deskjet 600c"
(→Analysis Of The Paper Feeder)
(→Analysis Of The Paper Feeder)
|Line 586:||Line 586:|
[[Image:DVForceAdvance.jpg|left|thumb||Force Of The Motor on Paper Feeder Rollers]]
Revision as of 22:17, 25 March 2007
This inkjet printer is manufactured by Hewlett Packard, and is used to transpose displayed digital data onto a physical medium.
How It Prints
The computer sends a data stream to the printer through a serial, or usb cable. The control unit inside the printer deciphers the data and instructs the mechanical components to act accordingly. The following is an illustrated outline of the mechanical aspect.
1) Paper is advanced into position by the rubber rollers, which are powered by a stepper motor.
2) Another stepper motor, undocks the printer carriage. The dock is used to secure the carriage, and to keep the printer head clean.
3) The printer carriage is operated by a drive belt, which is powered by a third stepper motor.
4) The printer cartridge applies ink onto the paper according to the instructions supplied by the CPU through the copper contacts.
The table belows lists the components for the HP Deskjet 600c printer:
|Part #||Part Name||Category||Function||Material||Picture|
|1||Paper Tray||Structural Component||Holds Paper that is to be loaded in place||Plastic|
|2||Printer Housing||Structural Component||Protects internal components from the environment||Plastic|
|3||Large Stepper Motor||Input||Provides motion to the paper feeder mechanism||Metal casing, copper wire, magnet, gear|
|4||Docking Station Motor||Input||Controls the motion of the docking station||Metal casing, copper wire, magnet, gear|
|5||Printer Cartridge Holder and Rail||Output||Slides the Printer head along the railing from left to right||Plastic housing and metal rail|
|6||Paper Feed Gears||Transmission||Takes the input from the feed motor and controls the feeding of the paper||One plastic gear and one metal gear|
|7||CPU and Power Source||Input||Controls the entire printer and modulates the power input||Silicon, lead, copper, resistors, capacitors|
|8||Paper Ejector and Advancer Mechanism||Motion Conversion||Lowers the black bar so paper ejects cleanly, and raises bottom tray||Plastic|
|9||Print Head Motor||Input||Provides motion to print head||Metal case, copper wire, magnet, gear|
|10||Docking Station||Motion Conversion / Structural||Cleans and houses printer head when not printing||Plastic|
Computer Rendered Components
Drive Belt System
Paper Advancing Rollers
Cool Animated Videos
<embed src="http://www.youtube.com/v/8_iTSznToHU" type="application/x-shockwave-flash" width="425" height="350"></embed>
Animated Printer Carriage
<embed src="http://www.youtube.com/v/iayt04lR08E" type="application/x-shockwave-flash" width="425" height="350"></embed>
Animated Paper Feed Mechanism
Analysis Of The Belt System
Scope of Analysis
The two engineering specifications that are quantified for the printer belt tensioning system, are the force on the belt required to accelerate the printer head to its maximum speed, and the force to stop the printer carriage and change direction. Both of these specifications pertain to the Dots Per Inch design parameter. The best design is to obtain the maximum DPI rating in the quickest printing time. To achieve this goal, the belt must be able to cope with the forces to accelerate the printer carriage.
- Printer Prints 4 pages a minute at 300 DPI
- Mass of Carriage With Ink Cartridge = 0.14 kg
- Moment of Inertia of Pulley = 0.5 (.002kg)(0.005^2m) = 2.5 x 10^8
- The belt is a trapezoidal design, meaning each tooth has the shape of the trapezoid
- The belt is made out of polyurethane which has good wear resistance and low friction
Friction force exerted by the slider on the carriage is always constant when moving, and should have been reduced to a minimum by the manufacturer. Lower friction would reduce the force the stepper motor has to supply to move the carriage. Since it is difficult to measure the exact amount of friction force, and it is relatively small compared to the acceleration forces, friction can be neglected.
Finding The Speed
Since, the actual printer head speed I could not be found, a few assumptions had to be made with the available information. The printer has a 300 DPI rating, which means that it can print 90,000 dots per square inch. It can print 4 pages of text per minute. Assuming that it prints 8.5” x 11” pages with a 1” top and bottom margin, and 1.25” side margins, it leaves a total of 54 square inches of text. This equates to 4.86 x 10^6 dots per page. Multiply the dots per page by the pages per minute, and that results in 2.43 x 10^7 dots per minute. 2.43 x 10^7 dots per minute is the average printing rate for the printer. However, if we assume the format is 12 point, Times New Roman font, the total area per line of text is 1.95 in^2 (6.5” x .3”) 0.54 square inches per page multiplied by 4 pages per minute, divided by 1.95 square inches per pass, and taking the reciprocal, yields .009 minutes per line, which is 0.54 seconds per line. Every line is 6.5 inches long, which means that the printer head moves at 12 inches per second. Since information on the acceleration of the printer carriage could not be obtained, it was instead estimated. After careful observation of other inkjet printers, the carriages reach their top speed almost instantaneously, so it was estimated that it takes 0.2 seconds to reach maximum velocity, and 0.25 seconds to stop and change direction.
- Acceleration of Carriage From Rest
Acceleration of Carriage = max velocity/ time = (0.3048 m/s) / 0.2 s = 0.15 m/s2
Mass of Carriage With Ink Cartridge = 0.14 kg
F = ma = (0.14)(0.15) = 0.021 N
Therefore, it takes .021 N to accelerate the carriage from rest to the max velocity
- Stopping and Changing Direction
Change in velocity = (0.3048+.03048) = 0.6096 m/s
Change in Time = 0.25 s
F = (Mass*Change in Velocity)/ Change in time = 0.34 N
Therefore, the maximum force exerted on the belt due to the change in direction is 0.34 N.
As seen in Figure 10 below, the maximum force to pull the carriage is related to the torque supplied by the motor pulley. Furthermore, the carriage is fixed to one side of the belt, so it translates directly with the belt. During the analysis, the entire carriage is treated as a point mass and represented as a block. Figure 11 shows the free body diagram of the motor pulley. It is evident that the torque from the pulley is directly related to the force on the belt during acceleration.
The analysis through Adams produced results that were similar to the calculated values. The maximum force, as seen in Figure 12, reached 1 N which was very close to the calculated value of 0.34 N.
To increase the maximum force that the belt could handle, a few options are available. The cross-sectional area could be increased to decrease the stress on the belt. According the stress equation, stress = load / area , the stress can be reduced by increasing the cross sectional area to compensate for load force. The cross sectional area can be increased by making the belt wider or thicker. Making it wider would be more beneficial because it would provide a greater surface area for the toothed pulley to grip onto. The drawbacks for increasing the surface are the increase in stiffness and cost of manufacturing. Making the belt thicker would reduce its flexibility, making it harder for it to move around the pulley. It would require more torque form the input motor to compensate. Making the belt wider would force the pulleys to be wider, which drives up the cost of the system.
Another method to increase the stress capacity of the belt would be to use a curvilinear design instead of the current trapezoidal design. The curvilinear design looks very similar to the gear sprocket of a bicycle. Instead of a trapezoid shape, the curvilinear design uses a half circle shape. Therefore, the teeth are deeper in the gear which makes it less probable for tooth jumping during high accelerations. Furthermore, there is less material at the edges of the gear, which lowers the moment of inertia, allowing the gear to accelerate faster. 
Figure 13 shows the photoelastic stress pattern of both designs, and it is evident that the curvilinear shape distributes stress more evenly. This is due to the larger tooth cross section. Since the curvilinear shape handles stress better than the trapezoidal shape, a narrower curvilinear belt could be used in place of a wider trapezoidal belt, thus, saving material and cost.  The trade off may be in increased cost to manufacture, since curvilinear belts are not as common as trapezoidal belts.
A final option to consider is to change the material of the belt. Using a more durable and stress resilient material such as steel or composites, may work better. However, it is most likely that these materials are more difficult to manufacture, which increases the cost
Analysis Of The Paper Feeder
The engineering specification chosen to analyze for this dissection was the force that was exerted on the two interlocking gears that managed the motion of the paper feed mechanism. This force was then translated into a stress and then examined to see if the gears would deform under the load. Both the geometry of the paper feeder and the size and type of motor contributed significantly to the loading of this problem. The larger the moment of inertia of the paper rollers and the center rod, the more resistance there is to the motion of the entire system, resulting in a larger gear force. The motor that was used in this model was a stepper motor. This was most likely chosen for its usefulness for moving the paper at a given increment. However, the stop and go nature of this motor increased the gear force by creating sudden starts and stops of the system rotation.
Analysis will have to be performed on the operating conditions of the printer. The coefficient of the rubber wheels on the paper will have to be found along with all of the geometric parameters of the system. For example, the radii of the wheels, their thickness, and their density will all have to be found in order perform the analysis in ADAMS. All geometric parameters, moments of inertia and yield strengths will be have to be found to perform the analysis. Finally, the force that is necessary to slide the paper (adding to the resistance of the motion) will also need to be found. This will be found by using the coefficient of friction mentioned earlier.
Simplifications in the model can be made in this analysis. Since we are only concerned with what is going on at the gears, the yield stresses will be unnecessary for the rod and the wheels. Also, the wheels (which are composed of both rubber and plastic) can be considered to be entirely rubber since the density of rubber is greater than that of plastic. If the calculations indicate that stresses are such that they are close to the yield stress, than this simplification will have to be done away with in order to get a more accurate value for the gear force.
Engineering Specification for Paper Feeder
Gear Force (and Stress)
- The force that is exerted on the two gears at their intersection (and the stress that results from this force).
- Target Value: Force < 1e5 N (from the 40 MPa Tensile Strength of Plastic)
- Direction of Improvement: Down (smaller gear force)
- Related user requirement: Paper feeds smoothly
Design decisions/parameters affected
- Geometry of System
- Size and Type of Motor
Key geometric, inertia, and material properties
- Length, radius, density of rod (stainless steel)
- Thickness, radius, density of Wheels (rubber)
- Thickness, radius, density of Gears (steel and plastic)
- Moment of inertia for all components
Brittle Fracture Analysis: Maximum Normal Stress Theory